|本期目录/Table of Contents|

[1]朱龙飞,朱建国,佟文明,等.过盈配合对非晶合金电机铁耗影响的实验研究[J].电机与控制学报,2016,20(09):40-45.[doi:10. 15938 / j. emc. 2016. 09. 006]
 ZHU Long-fei,ZHU Jian-guo,TONG Wen-ming,et al.Experimental research on influences of shrink fitting process to iron losses of amorphous alloy motor [J].,2016,20(09):40-45.[doi:10. 15938 / j. emc. 2016. 09. 006]
点击复制

过盈配合对非晶合金电机铁耗影响的实验研究(PDF)
分享到:

《电机与控制学报》[ISSN:1007-449X/CN:23-1 408/TM]

卷:
20
期数:
2016年09
页码:
40-45
栏目:
出版日期:
2016-09-01

文章信息/Info

Title:
Experimental research on influences of shrink fitting process to iron losses of amorphous alloy motor
作者:
朱龙飞1 朱建国2 佟文明1 韩雪岩1
 ( 1. 沈阳工业大学 国家稀土永磁电机工程技术研究中心 电气工程学院,辽宁 沈阳 110870; 2.悉尼科技大学 电气机械和机电系统学院,澳大利亚 悉尼 2007)
Author(s):
ZHU Long-fei1 ZHU Jian-guo2 TONG Wen-ming1 HAN Xue-yan1
 ( 1. School of Electrical and Engineering,National Engineering Research Center for Rare-earth Permanent Magnetic Machines,Shenyang University of Technology,Shenyang 110870,China; 2. School of Electrical Mechanical and Mechatronic System,University of Technology Sydney,Sydney 2007,Australia)
关键词:
过盈配合 非晶合金 永磁电机 铁耗 实验研究
Keywords:
shrink fitting amorphous alloy permanent magnet motor iron loss experimental research
分类号:
TM 351
DOI:
10. 15938 / j. emc. 2016. 09. 006
文献标志码:
A
摘要:
为了研究过盈配合加工对非晶合金永磁电机铁耗的影响,采用实验方法测试了多种过盈量 时非晶合金材料的损耗特性,并对实验结果进行了分析。给出了考虑过盈配合加工的非晶合金电 机铁耗计算方法,并通过样机实验对铁耗计算结果进行了验证,进而分析了不同过盈量时非晶合金 电机铁耗的变化规律。结果显示,过盈配合加工会导致非晶合金材料涡流损耗增加,非晶合金电机 轭部损耗增加、温升升高、效率降低。在非晶合金电机定子铁心装配时应采用尽可能小的过盈量或 不采用过盈配合工艺。
Abstract:
In order to research the influences of shrink fitting process to the iron losses of amorphous alloy permanent magnet motor,experimental method was adopted to measure the loss characteristics of amor-phous alloy material at several shrink ranges,and the results were analyzed. The iron losses calculation method of amorphous alloy motor was given which is in consideration of the influences of shrink fitting process. The calculated results were verified by measured results of an amorphous alloy motor,and the in-fluences of shrink fitting process to amorphous alloy motor was analyzed. The results show that,the eddy current part of amorphous alloy material and the yoke loss of amorphous alloy motor increase a lot because of the shrink fitting process,which leads to a increasing of temperature raise and decreasing of efficiency performance. So,the shrink range should be as small as possible or the shrink fitting process is not used during the casing of amorphous alloy motors.

参考文献/References:

相似文献/References:

[1]李超,徐启峰. 非晶合金J - A 模型修正[J].电机与控制学报,2014,18(07):86.
 LI Chao,XU Qi-feng. Amorphous alloys J-A model amendment[J].,2014,18(09):86.
[2]宋守许,许可,鲍晓华. 混合定子铁心再制造电机空载磁密规律[J].电机与控制学报,2019,23(08):92.[doi:10.15938/j.emc.2019.08.012]
 SONG Shou-xu,XU Ke,BAO Xiao-hua. Analysis of no-load magnetic flux density law of hybrid stator core for remanufacturing motor[J].,2019,23(09):92.[doi:10.15938/j.emc.2019.08.012]

备注/Memo

备注/Memo:
收稿日期: 2015 - 10 - 31
基金项目: 国家科技支撑计划项目( 2013BAE08B00) ; 国家自然科学基金( 51307111) ; 辽宁省教育厅科学技术研究项目( L2013049)
作者简介: 朱龙飞( 1988—) ,男,博士研究生,研究方向为特种电机及其控制;
朱建国( 1958—) ,男,教授,博士生导师,研究方向为电工磁性材料和新型电驱动系统;
佟文明( 1984—) ,男,博士,副教授,研究方向为特种电机及其控制;
韩雪岩( 1978—) ,女,博士,副教授,研究方向为特种电机及其控制
更新日期/Last Update: 2016-12-08