|本期目录/Table of Contents|

[1]杨玉波,王秀和,丁婷婷.一种削弱永磁同步电动机齿槽转矩的方法[J].电机与控制学报,2008,(05):520-523.
 YANG Yu-bo,WANG Xiu-he,DING Ting-ting.Method of reducing cogging torque of solid-rotor permanent magnet synchronous motors[J].,2008,(05):520-523.
点击复制

一种削弱永磁同步电动机齿槽转矩的方法(PDF)
分享到:

《电机与控制学报》[ISSN:1007-449X/CN:23-1 408/TM]

卷:
期数:
2008年05
页码:
520-523
栏目:
出版日期:
2008-09-15

文章信息/Info

Title:
Method of reducing cogging torque of solid-rotor permanent magnet synchronous motors
作者:
杨玉波王秀和丁婷婷
山东大学 电气工程学院
Author(s):
YANG Yu-boWANG Xiu-heDING Ting-ting
School of Electrical Engineering, Shandong University
关键词:
同步电机实心转子永磁同步电动机 齿槽转矩 有限元法 槽楔 磁极宽度
Keywords:
synchronous motors solidrotor permanent magnet synchronous motor cogging torque finite element method slot wedge polearc width
分类号:
TM351
DOI:
-
文献标志码:
A
摘要:
为了研究实心转子永磁同步电动机的削弱措施,结合永磁电机永磁体极弧系数和永磁体不对称放置的方法,提出了一种仅改变实心转子非磁性槽楔的齿槽转矩削弱方法。通过非磁性槽楔的变化改变一个磁极的极弧宽度,其余磁极宽度不变,同时保持各个非磁性槽楔的宽度相同,通过合理的选择槽楔的形状和宽度,可以非常有效地削弱齿槽转矩。通过解析法研究了采用该方法后实心转子永磁同步电动机齿槽转矩的表达式,得到了永磁体剩磁平方的傅立叶分解表达式。据此得到了磁极的两种极弧宽度和磁极间距大小与齿槽转矩的关系式和磁极极弧宽度的确定方法。该方法仅改变了槽楔的形状,对电机结构影响较小,且合适极弧宽度组合较多,有限元验证表明该方法可有效地削弱齿槽转矩。
Abstract:
A new method is advised to reduce the cogging torque of solidrotor permanent magnet synchronous motor. Only changing the nonmagnetic slot wedge, was the pole arc width of one pole changed in this method, and the interval between two adjacent poles was the same. By suitably selecting the shape and width of nonmagntic slot wedge, the cogging torque could reduced. The analytical expression of cogging torque of solidrotor PM synchronous motor with this method was got. Based on the analytical expression, the Fourier expression of the square of residual flux density of PM was got. Then the method to calculate the width of pole arc was advised. At last, the finite element method was used to calculate the cogging torque of one prototype, and the results verify that the cogging torque can be greatly reduced with this method.

参考文献/References:

-

相似文献/References:

[1]侯利民,张化光,刘秀翀,等.永磁同步电机转子磁位自检测复合方法[J].电机与控制学报,2008,(05):498.
 HOU Li-min,ZHANG Hua-guang,LIU Xiu-chong,et al.Compound rotor position self-sensing method of PMSM[J].,2008,(05):498.
[2]苏健勇,杨贵杰,李铁才.PMSM扩展状态滑模观测器及转子位置和速度估算[J].电机与控制学报,2008,(05):524.
 SU Jian-yong,YANG Gui-jie,LI Tie-cai.Extended state sliding mode observer of PMSM and estimation of rotor position plus speed[J].,2008,(05):524.
[3]葛琼璇,李耀华,孔力.位置信号延时对牵引力控制性能的影响分析[J].电机与控制学报,2008,(05):534.
 GE Qiong-xuan,LI Yao-hua,KONG Li.Influence of time-delay of position signal on the performance of the thrust control[J].,2008,(05):534.
[4]司纪凯,汪旭东,陈昊,等.永磁直线同步电机出入端磁阻力齿槽分量分析[J].电机与控制学报,2008,(05):550.
 Ji kai,WANG Xu-dong,et al.Analysis of the slot-teeth component in permanent magnet linear synchronous motor at the outlet end[J].,2008,(05):550.
[5]张凤阁,白海军,刘宇,等.永磁外转子爪极发电机的漏磁计算[J].电机与控制学报,2009,(04):548.
 ZHANG Feng-ge,BAI Hai-jun,LIU Yu,et al.Leakage magnetic calculation on claw pole machine with outer permanent magnet rotor[J].,2009,(05):548.
[6]吴轩钦,谭国俊,宋金梅,等.基于混合磁链观测器电励磁同步电机矢量控制[J].电机与控制学报,2010,(03):62.
 WU Xuan-qin,TAN Guo-jun,et al.Electrically excited synchronous motor vector control based on hybrid air gap flux estimator[J].,2010,(05):62.
[7]李兵强,林辉.面装式永磁同步电机增磁增矩负载角恒定控制[J].电机与控制学报,2010,(05):56.
 LI Bing-qiang/a>,LIN Hui.Torque increase by field-enhancing with constant load-angle control for SPMSM[J].,2010,(05):56.
[8]陈学珍,辜承林.组合转子同步电机稳定性探讨[J].电机与控制学报,2010,(12):41.
 CHEN Xue-zhen,GU Cheng-lin.Research on stability of hybrid rotor synchronous machine[J].,2010,(05):41.
[9]路义萍,丰帆,孙明琦,等.同步电机定子与气隙流场数值计算与分析[J].电机与控制学报,2011,(08):47.
 LU Yi-ping,FENG Fan,SUN Ming-qi,et al.Numerical calculation and analysis of fluid flow field of stator and air-gap of a synchronous machine[J].,2011,(05):47.
[10]路义萍,丰帆,王佐民,等.同步电机定子三维温度场数值模拟[J].电机与控制学报,2012,(03):42.
 LU Yi-ping,FENG Fan,WANG Zuo-min,et al.Numerical simulation of 3D temperature field for the stator of a synchronous machine[J].,2012,(05):42.

备注/Memo

备注/Memo:
基金项目:国家自然科学基金(50677035),作者简介: 杨玉波(1978-),男,博士,主要研究方向为永磁电机;王秀和(1967-),男,博士,教授,主要研究方向为永磁电机及其控制、电磁场分析、电机设计专家系统;丁婷婷(1981-),女,博士研究生,主要研究方向为微特电机与控制。
更新日期/Last Update: 2008-12-11